Repulsion induction motor

The induced emf induces current in the armature conductors and the direction of the induced current depends on the position of the brushes. Brush shift can also be used to control the speed of a repulsion motor. In this condition, the N-pole of the stator field will repel the N-pole of the rotor field and the S-pole of stator field will repel the S-pole of the rotor field, so the rotor starts rotating.

Uploader: Tozil
Date Added: 24 March 2014
File Size: 46.7 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 10001
Price: Free* [*Free Regsitration Required]





See the editorial for more information Brush holders and brushes are mounted in the commutator end bell, and the brushes, connected by a heavy wire, press against segments on opposite sides of the commutator see Fig. These were used where high starting torque was required. In the inductikn article we discussed about the basic principles of repulsion motors and how the repulsion principle aids in rotating a motor.

If the indjction axis is along the direction of the magnetic field, the armature behaves like an electromagnet and a N-pole is formed directly below the N-pole of the stator and a S-pole is formed directly above the S-pole of the stator. It has brushes that lift instantly once the motor starts. As the motor speeds up the reactance of the squirrel-cage decreases. Introduction In the previous article we discussed about the basic principles of repulsion motors and how the repulsion principle aids in rotating a inducrion.

Repulsion-start induction-run motor | HVAC Troubleshooting

These rods push against a short-circuiting ring mounted on the shaft on the commutator end of the armature. Due to quadrature drop cross-magnetizing effect occurs which opposes the mmf waves.

Home Articles Forum Glossary Incuction. The repulsion-induction motor repulsoin on one principle of operation and, when almost up to speed, changes over to another type of operation. What is the advantage in running the motor as a squirrel cage one? The cool thing was, it was ALL powered by a single 25HP Repulsion Induction motor and all of the machinery was interconnected by leather belts, shafts and pulleys.

Repulsion-induction Motor | Electrical Engineering Assignment

The armature turns faster and faster, accelerating until it reaches what is approximately 80 percent of the run speed. The maximum torque is obtained from a brush shift of 45 degrees. This is the modified indkction of the basic repulsion motor. This allows very fine control of speed.

Sachmanram liked this post. The basic design of this simplified machine is shown in FIG.

The Repulsion-Induction Motor

The two repulsion forces are in direct opposition to each other and hence no torque will be developed. Alternator Electric generator Inchworm motor. The starting-current inrush is from 2 to 4 times the full-load current.

The answer is YES, it is possible. For this purpose a centrifugal force-operated device is used.

Repulsion-start induction-run motor

Somewhere in the vicinity of 80 percent of synchronous speed, induction-motor action begins to predominate. It's powered by a 2 hp.

This coupling between the windings makes the starting torque slightly less than that obtained in the switch-type repulsion-start motor previously discussed.

Now let us discuss the various disadvantages of a conventional repulsion motor and how the various types are used to minimize those disadvantages, followed by repulsion induction motor wiring study.

Views Read Edit View inductlon. The repulsion-induction motor can be called a sophisticated version of the kotor motor just described. Brush shift can also be used to control the speed of a repulsion motor. But during normal running condition, the squirrel cage winding supplies most of the torque and commutator winding supplies relatively lower torque when compared to Squirrel cage winding.

Why Look for Chemistry Homework Help? The repulsion-induction motor has the following merits:

2 thoughts on “Repulsion induction motor”

Leave a Reply

Your email address will not be published. Required fields are marked *